Best Seller Items
-
PAM8403 5V Two-channel Stereo Mini Class-D Audio Amplifier
- Dual channel stereo, high output power (3 w + 3 w power @ 5V and 4 ohms load)..
- Double panel wiring solves crosstalk.
- Super mini design allows it to be easily placed in a variety of digital products.
- 3W Output at 10% THD with a 4ΩLoad and 5V Power Supply.
- Filterless, Low Quiescent Current and Low EMI and Low Noise.
- Short Circuit Protection and Thermal Shutdown
₹28.00₹50.00inc.GSTPAM8403 5V Two-channel Stereo Mini Class-D Audio Amplifier
₹28.00₹50.00inc.GST -
ATMEGA328 OR ATMEGA8 Arduino breakout board PCB with components unsoldered (Colour may vary)
- High quality FR4 double side pcb.
- ATMEGA328 or ATMEGA8
₹77.00₹150.00inc.GST -
CT Current Transformer 5A mini Sensor ZMCT103C DTCT103C (Color may vary)
- Rated input current: 5A
- Rated output current: 5 mA
- Ratio: 1000: 1
- Linear range: 0-10 A (100 Ohm)
- Linearity: 0.2%
- Insulation voltage: 3000 V
₹33.00₹70.00inc.GSTCT Current Transformer 5A mini Sensor ZMCT103C DTCT103C (Color may vary)
₹33.00₹70.00inc.GST -
TPA3116D2 2.1 Channel Digital Subwoofer Amplifier Board DC, 12-24 V, 2 x 50 W + 100 W
- Applicable speaker impedance: 4-8 ohm.
- Adopts two high-quality TPA3116D2 digital amplifier chips.
- Powered by DC 12-24V, wide input voltage.
- Sound quality is very good, high efficiency and amplifying power.
- 50W x 2+100W Â 2.1 channels(left/right channel and subwoofer channel), high efficiency and low-heat.
- User can adjust the volume by themselves easily.
₹1225.00₹1899.00inc.GSTTPA3116D2 2.1 Channel Digital Subwoofer Amplifier Board DC, 12-24 V, 2 x 50 W + 100 W
₹1225.00₹1899.00inc.GST -
Piezoelectric Sensor Buzzer Transducer/Disc 27mm Piezo sensor
- Sound pressure level: 85DB 10cm
- The input voltage: 30vp-p max
- Operating Temperature: -20~70
- Clear sound
- Ultra-thin and lightweight
- Low power consumption for voltage type
₹6.00₹40.00inc.GSTPiezoelectric Sensor Buzzer Transducer/Disc 27mm Piezo sensor
₹6.00₹40.00inc.GST -
100 RPM Dual Shaft BO Motor
- Low density: lightweight, low inertia.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Rated Speed(After Reduction): 100 RPM
- Rated Torque: 0.35 Kg cm
₹66.00₹100.00inc.GST100 RPM Dual Shaft BO Motor
₹66.00₹100.00inc.GST
-
ARDUINO UNO R3 (ch340) Micro Controller Board with Cable compatible (Make in india)
Model Type UNO Rev R3 Microcontroller Chip ATmega328 Operating Voltage (VDC) 5 Input Voltage(Recommended) 7-12V Input Voltage (limit) 6-20V Analog I/O Pins 6 Digital I/O Pins 14 (of which 6 provide PWM output) PWM Digital I/O Pins 6 DC Current per I/O Pin (mA) 40 DC Current for 3.3V Pin (mA) 50 Clock Speed 16 MHz SRAM (KB) 2 EEPROM 1 KB (ATmega328) Flash Memory 32 KB On Board LEDs On/Off, L (PIN 13), TX, RX Dimensions in mm (LxWxH) 75 x 54 x 12 Weight (gm) 28 (without cable) 54 (with cable) ₹400.00₹900.00inc.GSTARDUINO UNO R3 (ch340) Micro Controller Board with Cable compatible (Make in india)
₹400.00₹900.00inc.GST -
-
STM 32F103C8T6 ARM STM32 Development Board Module unsoldered
1, stm32F103C8T6Package Type: LQFP;Number of pins: 48;Kernel: Cortex-M3;Operating frequency: 72MHz;Storage resources: 64K Byte Flash, 20KByte SRAM;Interface Resources: 2x SPI, 3x USART, 2x I2C, 1x CAN, 37x I / O ports,Analog-to-digital conversion: 2x ADC (12-bit / 16-channel)Timers: 3 general timers and 1 advanced timerDebug Download: Support JTAG / SWD debug interface to download, support for IAP.2, RT9193: 3.3V regulator chip, the maximum output of 300mA.1, SWD interface: support for simulation, download and debug.2, Mirco USB interface: power supply and USB communication, does not support the download.3, USART1 interface: USART1 can be used to download the program, or use the USART1 for communication.4, MCU pin interface: leads all I / O port pins, easy to connect with peripherals.5, 5V and 3.3V power input and output interface: commonly used in external power supply, or with other modules for common ground treatment₹414.00₹600.00inc.GSTSTM 32F103C8T6 ARM STM32 Development Board Module unsoldered
₹414.00₹600.00inc.GST -
A2212 10T 1400KV Brushless Motor for Drone (Soldered Connector)
- Model: A2212/10T
- Motor KV: 1400
- Max. Efficiency Current: 6-12A
- No Load Current: 0.7A @10V
- Current Capacity: 16A/60S
₹420.00₹600.00inc.GSTA2212 10T 1400KV Brushless Motor for Drone (Soldered Connector)
₹420.00₹600.00inc.GST -
TPA3116D2 TPA3116 DC12-26V 100W Mono Digital Power Amplifier Digital Audio Amplifier
Chip type:Â TPA3116D2
Input voltage: DC12-26V
Output power: 100W
SNR: 100dB
Channel:Â Mono
Size: 79*54*16mm₹462.00₹530.00inc.GSTTPA3116D2 TPA3116 DC12-26V 100W Mono Digital Power Amplifier Digital Audio Amplifier
₹462.00₹530.00inc.GST -
12V DC 1/2″ Electric Solenoid Water Air Valve Switch (Normally Closed)
- Rated Operating Voltage: 12V DC.
- Rated Current: 0.6A.
- Operation Mode: NC (Normally Closed).
- Pressure: 0.02 – 0.8MPa.
- Max fluid temperature: 100°C.
₹472.00₹500.00inc.GST12V DC 1/2″ Electric Solenoid Water Air Valve Switch (Normally Closed)
₹472.00₹500.00inc.GST -
Nodemcu Wifi Development Board Esp32 30pin
- Built-in Flash: 32Mbit
- Power supply: 5V
- WiFi protocol: IEEE 802.11 b/g/n
- Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S
- Logic level: 3.3V
₹480.00₹565.00inc.GSTNodemcu Wifi Development Board Esp32 30pin
₹480.00₹565.00inc.GST -
LCD 20*4 Display
- Character Color: Black
- Supply voltage: 5V
- Dimensions: 98 x 60 x 12 (LxWxH) mm.
- 20 characters wide, 4 rows
- The module can easily interface with an MCU
- The module is a low-power consumption character LCD Module with a built-in controller
- Single LED backlight included can be dimmed easily with a resistor or PWM.
- Can be fully controlled with only 6 digital lines! (Any analog/digital pins can be used)
₹484.00₹700.00inc.GSTLCD 20*4 Display
₹484.00₹700.00inc.GST -
ESP-WROOM-32 ESP32 Development Board 38pin
1. 2.4GHz Dual-Mode WiFi + Bluetooth Development Board, 38PIN
2. Ultra-Low power consumption works perfectly with the IDE
3. Support LWIP protocol, Freertos
4. Support Three Modes: AP, STA, and AP+STA
5. ESP 32 is safe, reliable, and scalable to a variety of applications₹503.00₹750.00inc.GSTESP-WROOM-32 ESP32 Development Board 38pin
₹503.00₹750.00inc.GST -
PIC16F873-04/SP – MICROCHIP
Processor: It is based on the 8-bit PIC architecture, specifically the PIC16 family.
CPU Speed: The maximum CPU speed of the PIC16F873-04/SP is 4 MHz.
Flash Memory: It has 7.37 KB (8192 words) of flash program memory for storing the user’s program code.
RAM: The microcontroller has 192 bytes of RAM for data storage.
I/O Pins: It has a total of 22 I/O pins, which can be configured as digital inputs or outputs.
Timers: The PIC16F873-04/SP features three timers: Timer0, Timer1, and Timer2. These timers can be used for various timing and counting purposes.
Analog-to-Digital Converter (ADC): It includes an 8-channel, 10-bit ADC module that can convert analog signals into digital values.
Serial Communication: The microcontroller supports multiple serial communication protocols, including UART (Universal Asynchronous Receiver-Transmitter) and SPI (Serial Peripheral Interface).
Interrupts: It has several interrupt sources that can be used to handle external events and improve the responsiveness of the system.
Power-Saving Features: The PIC16F873-04/SP includes power-saving features such as a low-power sleep mode, which helps conserve energy in battery-powered applications.
Operating Voltage: It operates at a voltage range of 2.0V to 5.5V, making it suitable for a variety of applications.
Package: The PIC16F873-04/SP is available in a 28-pin plastic DIP (Dual Inline Package) or SPDIP (Shrink Plastic Dual Inline Package).
₹567.00₹697.00inc.GSTPIC16F873-04/SP – MICROCHIP
₹567.00₹697.00inc.GST -
ISD1820 Recording Module Voice Board With On Board Mic and Loud Speaker
- The main chip: ISD1820.
- Operating Voltage:Â DC 3V-5V.
- Loudspeaker: 8Ω, 0.5W.
- An easy to use 10 seconds of voice recording.
- High-quality, natural voice restored.
- Can be used as a propaganda module.
- With looping, jog playback, single-pass play function.
₹577.50₹600.00inc.GSTISD1820 Recording Module Voice Board With On Board Mic and Loud Speaker
₹577.50₹600.00inc.GST -
SIM800L GPRS GSM Module Board with power supply and antenna ( color may vary)
- Maximum input voltage 18V dc
- INBUILT ANTENNA
- HIGH EFFICIENCY STEP DOWN CONVERTER
- USE 12V 1A SUPPLY TO POWER
- TTL serial port for serial port, you can link directly to the micro-controller.
- Don’t need MAX232.
- Power module automatically boots, homing network.
₹578.00₹650.00inc.GSTSIM800L GPRS GSM Module Board with power supply and antenna ( color may vary)
₹578.00₹650.00inc.GST -
ESP32-CAM 2MP Wi-Fi Bluetooth Development Board with OV2640 Camera Module
- Flash LED off: 180mA @ 5V.
- Flash LED on to maximum brightness: 310mA @ 5V.
- Deep-sleep: 6mA @ 5V min.
- Modem-sleep: 20mA @ 5V min.
- Light-sleep: 6.7mA @ 5V min.
₹614.00₹800.00inc.GSTESP32-CAM 2MP Wi-Fi Bluetooth Development Board with OV2640 Camera Module
₹614.00₹800.00inc.GST -
Stepper Motor Nema-17
200 steps per revolution, 1.8 degrees
Bipolar stepper, requires 2 full H-bridges!
4-wire, 8 inch leads
42mm/1.65″ square body
31mm/1.22″ square mounting holes, 3mm metric screws (M3)
5mm diameter drive shaft, 24mm long, with a machined flat
12V rated voltage (you can drive it at a lower voltage, but the torque will drop) at 350mA max current
28 oz*in, 20 N*cm, 2 Kg*cm holding torque per phase
35 ohms per winding
₹630.00₹731.60inc.GSTStepper Motor Nema-17
₹630.00₹731.60inc.GST -
Heart Rate Monitor Kit with AD8232 ECG sensor module
- Designed to extract, amplify, and filter small biopotential signals.
- Leads-Off Detection.
- Shutdown Pin.
- LED Indicator.
- Analog Output.
- 3.5 mm Jack for Biomedical Pad Connection.
₹643.00₹700.00inc.GSTHeart Rate Monitor Kit with AD8232 ECG sensor module
₹643.00₹700.00inc.GST -
ST Link V2 Programmer For STM8 and STM32 ( color may vary )
- PCB installed inside of aluminum alloy U disk shell, portable, safe and reliable!
- Interface definition directly marked on the shell, clear, convenient and practical!
- 5V, 3.3V offers at the same time, allowing you to program your target board with both 5V and 3.3V.
- SWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector.
- SWIM programming speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speed.
₹650.00 inc.GSTST Link V2 Programmer For STM8 and STM32 ( color may vary )
₹650.00 inc.GST